Highly oriented α-Al2O3 transparent ceramics shaped by shear force

Alumina platelets were arranged horizontally in submicron alumina particles by shear force in the flow of slurries during casting. The obtained alumina green bodies with platelets were pressureless-sintered in vacuum, producing ceramics with thoroughly oriented grains and high transmittance. The effects of sintering parameters on the densification, microstructure evolution, and orientation degree of alumina ceramics were investigated and discussed. The results showed that the densification, grain size, orientation degree, and in-line transmittance were increased with increasing sintering temperature. The enhancement of orientation degree was mainly coherent with grain growth. The grain-oriented samples exhibited a much higher in-line transmittance (at 600 nm) of 61 % than that of the grain random sample (29 %). Moreover, the transmission remained a high level in the ultraviolet range (<300 nm).     

Irradiation-induced large bubble formation and grain growth in super nano-grained ceramic

In this work, 0.5TRPO•0.5Gd₂Zr₂O₇ ceramic with an average grain size of only ∼15 nm was prepared by a high pressure (5 GPa/520 °C) sintering method. Phase evolutions and microstructure changes of the as-fabricated super nano and micron-grained ceramics under a high-dose displacement damage induced by 300 keV Kr²⁺ ions were investigated. The results show that the super nano-grained ceramic has low degree of amorphization, obvious grain growth (2–3 times in grain size) and big Kr bubbles (10–68 nm) formation after irradiation. The micron-grained ceramic was severely amorphized after irradiation and many microcracks were formed parallel to its surface. The formation mechanism of Kr bubbles in the super nano-grained ceramic is on account of grain boundary diffusion and migration induced by the accumulation of the injecting Kr ions and irradiation defects. Nevertheless, microcracks formed in the micron-grained sample are caused by the accumulation of Kr atoms.     

基于Matlab的量子激光雷达稳频通信模拟系统设计

传统通信模拟系统设计较为复杂,导致模拟过程消耗能量较大,不能准确模拟稳频通信质量。因此,提出基于Matlab的量子激光雷达稳频通信模拟系统。由于振荡器是雷达形成初始信号源的基础,通过分析振荡电路与相位噪声,获得相位噪声函数与通信频率存在的关系;为确保通信过程的稳定,将准确性与稳定性作为信号质量的评价指标,并采用锁频环稳频技术计算频率偏移程度,根据PID控制算法控制频率,量子激光雷达稳频通信;利用Matlab确定激光器、探测器等硬件组成结构,通过时序与数字阵列的设置完成模拟系统设计。仿真结果表明所提系统结构简便、性能稳定,能够真实模拟出稳频通信的信号质量。     

抗FGF-2纳米抗体抑制碱烧伤诱导大鼠角膜血管新生

目的：研究抗成纤维细胞生长因子（FGF-2）纳米抗体对碱烧伤诱导的大鼠角膜血管生成的治疗作用。方法：将SD大鼠分为：假手术组（Sham），模型组（Model，直径为3 mm的浸有1 mol/L NaOH溶液圆形滤纸贴于大鼠眼角膜中央处30 s，制备大鼠碱烧伤血管生成模型）和治疗组（Treatment，术后7天至21天用3 mg/mL的抗FGF-2纳米抗体溶液滴眼，每日3次，每次10 μL，共14天）。通过体视显微镜和CD31免疫组织化学染色计算大鼠角膜血管生成情况。实时荧光定量PCR、酶联免疫吸附测定和免疫组织化学染色3种方法检测抗血管内皮生长因子（VEGF）和FGF-2的mRNA和蛋白表达水平。结果：（1）血管：治疗组较模型组的面积显著减少，血管管腔较窄（P<0.05），在药物干预14天后，差异最为显著；（2）FGF-2的mRNA和蛋白表达水平：模型组与治疗组的结果相近（P>0.05）；（3）VEGF的mRNA和蛋白表达水平：治疗组显著高于模型组（P<0.05）。此外，假手术组的持续给药也使得VEGF表达显著增加（P<0.05）。 结论：抗FGF-2纳米抗体可抑制由碱烧伤诱导的角膜血管新生，但也使得正常大鼠角膜或病理大鼠角膜的VEGF表达水平代偿性升高。     

Direct writing of textured ceramics using anisotropic nozzles

Direct writing is a unique means to align anisotropic particles for the fabrication of textured ceramics by templated grain growth (TGG). We show that alignment of tabular barium titanate (BT) template particles (20–40 μm width and 0.5–2 μm thickness) in a PIN-PMN-PT matrix powder (d₅₀ = 280 nm) is significantly improved during direct writing using anisotropic nozzles at high printing rates. The particle orientation distribution in as-printed filaments, and the texture orientation distribution in sintered ceramic filaments are shown to directly correlate with COMSOL Multiphysics-predicted torque distributions for direct writing with aspect ratio 2, 3 and 5 oval nozzles. Electromechanical strain properties of the textured piezoelectric ceramics significantly improved relative to random ceramics when printed with anisotropic nozzles. Simulations of aspect ratio 20 nozzles and nozzles with interior baffles demonstrate significantly increased torque and near elimination of constant shear stress cores (i.e. plug flow).     

Testing EGFR with Idylla on Cytological Specimens of Lung Cancer: A Review

The current standard of care for advanced non-small-cell lung cancer is based on detecting actionable mutations that can benefit from targeted therapy. Comprehensive genetic tests can have long turn-around times, and because EGFR mutations are the most prevalent actionable mutation, a quick detection would enable a prompt initiation of targeted therapy. Furthermore, the scarcity of diagnostic material means that sometimes only cytologic material is available. The Idylla™ EGFR assay is a real-time PCR–based method able to detect 51 EGFR mutations in 2.5 h. Idylla is validated for use only on FFPE sections, but some researchers described their experiences with cytological material. We reviewed the relevant literature, finding four articles describing 471 cases and many types of cytological input material: smears, cell-block sections, suspensions, and extracted DNA. The sensitivity, specificity, and limit of detection appear comparable to those obtained with histological input material, with one exception: the usage of scraped stained smears as input may reduce the accuracy of the test. In conclusion, usage of cytological material as input to the Idylla EGFR test is possible. A workflow where common mutations are tested first and fast, leaving rarer mutations for subsequent comprehensive profiling, seems the most effective approach.     

Fabrication of bacterial cellulose with high efficient loading of Ag and TiO2 nanoparticles for removing organic dyes

As a new advanced oxidation technology, photocatalytic technology has broad application prospects in the field of wastewater treatment. However, in the actual use process, there will be difficulties in catalyst recovery and reuse. This article successfully prepared bacterial cellulose (BC) loaded silver and titanium dioxide nanoparticles (Ag-plated TiO₂/BC composite pellicle) by in situ embedding method. BC not only works as the carrier to load TiO₂ and Ag NPs but also adsorbs dyes to promote the reaction. As a reusable photocatalytic film, it is convenient to use and recycle in terms of testing and characterization compared with powders. The results show that Ag and TiO₂ nanoparticles were closely embedded in BC. We evaluated the photocatalytic degradation performance of the catalyst on methylene blue (MB), active red X-3B, and Rhodamine B. When the reaction time was 2 h, the dye removal rates were 71%, 68%, and 82.6%. At the same time, through the inhibition zone experiment, it was found that the material has a certain inhibitory effect on both Escherichia coli and Staphylococcus aureus. Therefore, the supported catalyst prepared by this method has the advantages of high catalytic activity, relatively stable property, easy recovery, and tailorability, making it potentially applicable in sewage post-treatment links.     

Impact of the Zr-substitution on phase composition,structure, magnetic,and microwave properties of the BaM hexaferrite

Rapid developments in information technologies and a large rise in electrical and electronic equipment have generated different forms of electronic environmental contamination. Microwave absorption materials are important to avoid the damage that can be caused by electromagnetic radiation. A necessary condition for the absorption of the most incoming radiation is balanced wave impedance at the air/shield interface, which depends on the studied materials' magnetic and electrical properties. The paper introduces the preparation of BaFe_12-xZr_xO₁₉ (x = 0.1, 0.3, 0.6, 0.9, and 1.2) using a solid-state reaction technique. The studied samples were examined by X-ray diffraction, scanning electron microscopy, vibrating sample magnetometer, and a vector network analyzer. The studied samples showed that controlling the grain size and the prepared samples' magnetic properties play an important role in enhancing the microwave radiation absorption. The examined samples can be a promising absorption material in electromagnetic shielding applications.     

A thermal perspective of flash sintering: The effect of AC current ramp rate on microstructure evolution

In flash sintering experiments, the thermal history of the sample is key to understanding the mechanisms underlying densification rate and final properties. By combining robust temperature measurements with current-ramp-rate control, this study examined the effects of the thermal profile on the flash sintering of yttria-stabilized zirconia, with experiments ranging from a few seconds to several hours. The final density was maximized at slower heating rates, although processes slower than a certain threshold led to grain growth. The amount of grain growth observed was comparable to a similar conventional thermal process. The bulk electrical conductivity correlated with the maximum temperature and cooling rate. The only property that exhibited behavior that could not be attributed to solely the thermal profile was the grain boundary conductivity, which was consistently higher than conventional in flash sintered samples. These results suggest that, during flash sintering, athermal electric field effects are relegated to the grain boundary.     

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (C_f/C) composite for spark plasma sintering, two kinds of commercially pure α-Al₂O₃ powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (T_sg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al₂O₃ powder and 1400 °C for the 3 μm Al₂O₃ powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al₂O₃ compact can reach ～80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.